Festo

DAPS-0480-090-RS4-F14-T4 — Quarter turn actuator

DAPS-0480-090-RS4-F14-T4 Quarter turn actuator

Part number DAPS-0480-090-RS4-F14-T4 · Order no. 8030624

Overview

Quarter turn actuator DAPS-0480-090-RS4-F14-T4. Pneumatic connection: G1/4; Torque at nominal operating pressure and 0° swivel angle: 480 Nm; Swivel angle: 90°; Flange hole pattern: F14; Shaft connection: T36

Technical data

Size of valve actuator 480
Flange hole pattern F14
Swivel angle 90°
End-position adjustment range at 0° -1 – 9°
End-position adjustment range at nominal swivel angle 81 – 91°
Shaft connection depth 38.5 mm
Note on end-position adjusting range One end position optionally adjustable
Fitting connection conforms to standard ISO 5211
Cushioning No cushioning
Mounting position optional
Mode of operation Single-acting
Design Scotch yoke system
Position detection Without
Closing direction Closes to the right
Valve connection conforms to standard VDI/VDE 3845 (NAMUR)
Safety Integrity Level (SIL) To SIL 2 Low Demand mode
Supply pressure for spring strength 0.56 MPa / 5.6 bar
Operating pressure 0.56 – 0.84 MPa / 5.6 – 8.4 bar
Nominal operating pressure 0.56 MPa
Max. swivel frequency at 0.6 MPa (6 bar, 87 psi) 1 Hz
CE mark (see declaration of conformity) To EU Explosion Protection Directive (ATEX)
UKCA marking (see declaration of conformity) To UK EX instructions
Certificate issuing authority German Technical Control Board North (TÜV Nord) 212170801
ATEX category gas II 2G
ATEX category dust II 2D
Explosion ignition protection type for gas Ex h IIC T6...T3 Gb X
Explosion ignition protection type for dust Ex h IIIC T85°C...T200°C Db X
Explosion ambient temperature -20°C <= Ta <= +150°C
Operating medium Compressed air to ISO 8573-1:2010 [7:4:4]
Note on operating and pilot medium Lubricated operation possible (in which case lubricated operation will always be required)
Corrosion resistance class CRC 3 - high corrosion stress
LABS (PWIS) conformity VDMA24364 zone III
Ambient temperature -20 – 150°C
Torque at nominal operating pressure and 0° swivel angle 480 Nm
Torque at nominal operating pressure and 50° swivel angle 240 Nm
Torque at nominal operating pressure and 90° swivel angle 320 Nm
Note on torque The operating torque of the actuator must not be higher than the maximum permissible torque listed in ISO 5211, with reference to the size of the mounting flange and of the coupling.
Spring return torque at 0° swivel angle 320 Nm
Spring return torque at 50° swivel angle 240 Nm
Spring return torque at 90° swivel angle 480 Nm
Spring strength 4
Air consumption at 0.6 MPa (6 bar, 87 psi) per cycle 0°-nominal swivel angle-0° 19.6
Product weight 22700 g
Shaft connection T36
Pneumatic connection G1/4
Note on materials RoHS-compliant
Material cover Wrought aluminium alloy
Material seals FPM, PTFE reinforced
Material housing Wrought aluminium alloy
Material screws High-alloy steel
Material shaft High-alloy steel
Material number shaft 1.4305

Often bought with

QS-G1/4-10 Push-in fitting QS-G1/4-10
QS-G1/4-10-I Push-in fitting QS-G1/4-10-I
QSL-G1/4-10 Push-in L-fitting QSL-G1/4-10

Similar products